Facility show

Continuing miniaturization of components and increasing complexity of boards is driving the need for PCB AOI Testing: Checks for missing components, offset, incorrec...

Chemical laboratory is a very important part of PCB dry and wet process. It is also an important base of technology research and development for enterprises. Therefore, i...

Electrical performance test is mainly to test continuity and insulation of substrate circuit. Continuity test refers to whether continuity of the circuit is determi...

PCB drilling machine is a machine used in the drilling process of PCB processing. PCBs must be drilled with holes in the board to allow the pins of the components to...

Drilling operations in addition to drilling blind holes, or very high level of precision requirements of the hole plate is very strict, with a single drill, usually with ...

Printed circuit board DES production line is the inner or outer acid etching of the development of + etching + stripping film line

Focused on the panel glass, electronics industry, according to the size of the PCB market, the market appeared PCB testing equipment NV small stroke automatic optical imager,...

Impedance Tester   Impedance tester for testing pcb parameters such as below that.At paresent,like such test is just simple for pwb industry,pcb...

Process: Spraying - Exposure - Developing - Curing - Etching The role of exposure; the customer's graphic data in the form of positive or negative transfer pcb, whil...

The inspection of the PCB hole inspection machine is considered a critical test step in the PCB and semiconductor industry. X-ray systems must provide high-resolution, h...

X-ray inspection machine is mainly for PCB board to check whether the targets of the layers are offset. X-ray inspection machine uses Before and after the PCB dr...

A magnifying glass with a circular tube to view line quality and alignment accuracy, if the outer layer still need to view the hole and coating quality, usually with 10 ...

Flying Probe Tester (Flying Probe Tester) is a type of instrument used to test PCB (printed circuit board) with high density, number of layers, large wiring density and ...

PTH (Plating Through Hole) Metallized hole, so the layer to which it is connected is conductive; there is an electrical connection. In contrast, NPTH (Non Plating Throug...

The Auto Drill Bit Sharpener is designed to help you with brick drilling without any mistakes in the brick, and the hole size of the brick will not exceed the specified r...

Atomic Absorption Spectrometer is used to check the surface of pcb,if every part appreas some errors,workers will right it and tell engineers for pcb design again.To...

Multi-layer PCB processing is essential to the use of the laminating machine, and laminating machine pressure uniformity and temperature uniformity of the quality of the...

Pre-treatment: 1. The inner layer pre-treatment: usually do not brushing, using micro-etching or electrolytic degreasing mode 2. Outer layer pretreatment: It usu...

Inner etching: The etching solution used, the main component of acid sodium chloride etching solution and alkaline sodium chloride etching solution, the resist is a dry ...

After the inner board circuit is completed, the integrity of the access and the insulation must be ensured, that is, the same inspection as the single panel is required. Bec...

Automated Optical Inspection (AOI), using high-speed high-precision visual processing technology to automatically detect a variety of different PCB mounting error and we...

PCB single-sided or double-sided board production are in the blanking directly after the non-vias or vias drilling, multi-layer board is completed after the pressure pla...

After the pattern electroplating in the outer dry film, the circuit part is electroplated with copper to prevent the part of the circuit from being etched when the etchi...

The electroplating process is to provide the metal coating with high conductivity, good solderability, high mechanical strength, and ductility to withstand the terminal ...

ENIG, chemical nickel gold. 1, the surface is flat (relative to spray tin, etc.); 2, solderable, can be wire (gold wire, aluminum wire), good heat dissipation; 3,...

Hot air leveling HASL, hot air solder leveling.It is a process of applying molten tin-lead solder to the PCB surface and leveling (blowing flat) with heated compressed a...

PCB equipment includes all kinds of production and testing equipment used in the PCB production process. In the electronics industry PCB automation equipment, high-preci...

Cutting is the first step in production process,the goal makes sure that the present overall appearance is in keeping with pcb design or not.This machine can be saw in e...

Dry Film protect the pwb surface ,prevent the surface oxided.The pcb processed by Dry Film can make the circuit board reflect,looked perfect and beautyful. Dry Film ...

Solder mark process the surface of pcb between two pcb.No matter rigid pcb or flex circuit are used in this machine,we should keep the environment clean for high product...

Routing embellishes the printed circuit board accoarding to the design before,the surface will be looked beautiful and smooth.By the routing machine,our pcb quality can ...

FQC means that workers check the detail information of pcb,making sure every pcb process is right.FQC includes product check,hole check and cleaning.It is just ...

PCB packing is the end process of pcb industry,common packing method is vacuum packaging, so to prevent the PCB surface is oxidized. General packaging of the PCB can not...

Final Audi consists of visual inspection engineering measure，it is the end step of the second tracking of quality control center.Workers by the Final Audi know that th...